[pvrusb2] pvrusb2 vs. em8300
Roger J. Allen
rja at firkraag.rogera.net
Wed Feb 15 19:57:06 CST 2006
On Wed, 15 Feb 2006, Roger J. Allen wrote:
> On Sun, 12 Feb 2006, Michael Roitzsch wrote:
>
>> Hi Mike,
>>
>
> I'll attach my dmesg output. It shows the pvrusb2 startup, a few
It looks like attachments are being dropped by the mailing list.
> lines of:
>
> i2c_adapter i2c-0: Transaction error!
>
> and then the em8300 and adv717x modules start and load their firmware.
> The pvrusb2 displays the messages about loading it's firmware.
> MythTV starts up the pvrusb2 and records the local news.
> I used xine to play the recording of the local news to the Dxr3 tv-out.
> Both audio and video seem to be working fine.
>
Linux version 2.6.15-1.1831_FC4 (bhcompile at tweety.build.redhat.com) (gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #1 Tue Feb 7 13:37:42 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5520
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.2 present.
ACPI: RSDP (v000 KT600 ) @ 0x000f6f40
ACPI: RSDT (v001 KT600 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 KT600 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: MADT (v001 KT600 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff7d80
ACPI: DSDT (v001 KT600 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC disabled (-2); pass 'lapic' to re-enable.
LAPIC disabled (-2)
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/123 vga=795 3
mapped APIC to ffffd000 (00000000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0413000 soft=c0412000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2200.385 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034064k/1048512k available (2148k kernel code, 13784k reserved, 774k data, 196k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4404.94 BogoMIPS (lpj=8809886)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) XP 3200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e20)
Local APIC disabled by default; use 'lapic' to enable it.
checking if image is initramfs... it is
Freeing initrd memory: 1188k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x4000-0x407f could not be reserved
pnp: 00:01: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e2ffffff
PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1140024005.840:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key BBAAC818B8690C98
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PCI: Bypassing VIA 8237 APIC De-Assert Message
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 10240k, total 262144k
vesafb: mode is 1280x1024x32, linelength=5120, pages=0
vesafb: protected mode interface info at c000:ce20
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
vesafb: Mode is VGA compatible
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (43 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 256M @ 0xc0000000
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:0f.0, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6L200R0, ATA DISK drive
hdb: Maxtor 6L300R0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-110D, ATAPI CD/DVD-ROM drive
hdd: Memorex 52MAXX 2452AJ, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 398297088 sectors (203928 MB) w/16384KiB Cache, CHS=24792/255/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdb: max request size: 1024KiB
hdb: 586114704 sectors (300090 MB) w/16384KiB Cache, CHS=36483/255/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 hdb13 >
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 UAR1 LPT1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Write protecting the kernel read-only data: 337k
logips2pp: Detected unknown logitech mouse model 79
SCSI subsystem initialized
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input1
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
scsi0 : AdvanSys SCSI 3.3K: PCI Ultra-Wide: PCIMEM 0xF8820000-0xF882003F, IRQ 0xB
Vendor: SEAGATE Model: ST15230N SUN4.2G Rev: 0702
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 8386733 512-byte hdwr sectors (4294 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 8386733 512-byte hdwr sectors (4294 MB)
SCSI device sda: drive cache: write through
sda: sda1
sd 0:0:1:0: Attached scsi disk sda
Vendor: SEAGATE Model: ST15230N Rev: 0638
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 8386733 512-byte hdwr sectors (4294 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 8386733 512-byte hdwr sectors (4294 MB)
SCSI device sdb: drive cache: write through
sdb: sdb1 sdb2 < sdb5 >
sd 0:0:2:0: Attached scsi disk sdb
Vendor: SEAGATE Model: ST32430N Rev: 0510
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdc: 4197405 512-byte hdwr sectors (2149 MB)
SCSI device sdc: drive cache: write through
SCSI device sdc: 4197405 512-byte hdwr sectors (2149 MB)
SCSI device sdc: drive cache: write through
sdc: sdc1
sd 0:0:3:0: Attached scsi disk sdc
Vendor: ARCHIVE Model: Python 02635-XXX Rev: 567D
Type: Sequential-Access ANSI SCSI revision: 02
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
st: Version 20050830, fixed bufsize 32768, s/g segs 256
st 0:0:5:0: Attached scsi tape st0<4>st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker at scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
natsemi eth0: NatSemi DP8381[56] at 0xe4114000 (0000:00:0b.0), 00:09:5b:61:12:c7, IRQ 10, port TP.
tg3.c:v3.47 (Dec 28, 2005)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
eth1: Tigon3 [partno(BCM95782A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:50:2c:09:8c:9d
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[763f0000]
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
Installing spdif_bug patch: Audigy 2 ZS [SB0350]
Linux video capture interface: v1.00
pvrusb2 pvr_init
usbcore: registered new driver pvrusb2
/usr/local/src/pvrusb2/pvrusb2-mci-20060209/driver/pvrusb2-main.c: Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner : 20060209 (from www.isely.net)
/usr/local/src/pvrusb2/pvrusb2-mci-20060209/driver/pvrusb2-main.c: Debug mask is 16834943 (0x100e17f)
gameport: EMU10K1 is pci0000:00:09.1/gameport0, io 0xc400, speed 1242kHz
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
i2c_adapter i2c-0: Transaction error!
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
em8300: EM8300 8300 (rev 2) bus: 0, devfn: 80, irq: 11, memory: 0xe4000000.
em8300: mapped-memory at 0xf9680000
em8300: using MTRR
em8300_main.o: Chip revision: 2
adv717x.o: ADV7175A chip detected
adv717x.o: Configuring for PAL 60
adv717x.o: Configuring for NTSC
em8300_audio.o: Analog audio enabled
em8300: Microcode version 0x29 loaded
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 11, io mem 0xe4118000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000dc00
usb 1-2: new high speed USB device using ehci_hcd and address 2
pvrusb2 pvr2_hdw_create: hdw=c1af8000
pvrusb2 Driver unit number is 0, name is pvrusb2_a
pvrusb2 subsys_stream_mask: 0x1e
pvrusb2 pvr_probe(pvr=f7024080)
pvrusb2 pvr2_hdw_setup(hdw=c1af8000) begin
pvrusb2 pvr2_upload_firmware1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
pvrusb2 cpureset_assert(1)
pvrusb2 Upload done, releasing device's CPU
pvrusb2 cpureset_assert(0)
pvrusb2 Upload done (8192 bytes sent)
pvrusb2 pvr2_hdw_setup(hdw=c1af8000) done, ok=1 init_ok=0
pvrusb2 Device microcontroller firmware (re)loaded; it should now reset and reconnect.
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:10.2, from 5 to 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:10.3, from 5 to 11
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 11, io base 0x0000e400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-2: USB disconnect, address 2
pvrusb2 pvr_disconnect(pvr=f7024080) BEGIN
pvrusb2 pvr2_hdw_disconnect(hdw=c1af8000)
pvrusb2 pvr2_hdw_remove_usb_stuff: hdw=c1af8000
pvrusb2 render_useless
pvrusb2 pvr2_hdw_destroy: hdw=c1af8000
pvrusb2 pvr_disconnect(pvr=f7024080) DONE
usb 3-1: new full speed USB device using uhci_hcd and address 2
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt 0000:00:09.2[B] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[e4115000-e41157ff] Max Packet=[2048]
ACPI: PCI Interrupt Link [LNKF] BIOS reported IRQ 0, using IRQ 10
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKF] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host1: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e4117000-e41177ff] Max Packet=[2048]
usb 1-2: new high speed USB device using ehci_hcd and address 4
pvrusb2 pvr2_hdw_create: hdw=f7202000
pvrusb2 Driver unit number is 0, name is pvrusb2_a
pvrusb2 subsys_stream_mask: 0x1e
pvrusb2 pvr_probe(pvr=f7024480)
pvrusb2 pvr2_hdw_setup(hdw=f7202000) begin
pvrusb2 Performing a device reset...
usb 1-2: reset high speed USB device using ehci_hcd and address 4
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
tuner 3-0061: chip found @ 0xc2 (pvrusb2_a)
pvrusb2 i2c_attach [client=(tuner unset) @ 0x61 ctxt=f71bab20]
msp3400 3-0040: chip=MSP3445G-B8 +nicam +simple +simpler +radio mode=simpler
msp3400 3-0040: msp34xxg daemon started
pvrusb2 i2c_attach [client=MSP3445G-B8 @ 0x40 ctxt=f720c780]
saa7115 3-0021: saa7115 found @ 0x42 (pvrusb2_a)
pvrusb2 i2c_attach [client=saa7115 @ 0x21 ctxt=f720c580]
tda9887 3-0043: chip found @ 0x86 (pvrusb2_a)
pvrusb2 i2c_attach [client=tda9887 @ 0x43 ctxt=f720c540]
pvrusb2 pvr2_upload_firmware2
pvrusb2 Requesting uproc soft reset
pvrusb2 Requesting uproc hard reset
ieee1394: Error parsing configrom for node 0-00:1023
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c015104a678]
ieee1394: Host added: ID:BUS[1-00:1023] GUID[00502c000009a298]
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
pvrusb2 upload of pvrusb2.f2 : 262144 / 262144
tveeprom 3-0050: Hauppauge model 29032, rev D168, serial# 7653922
tveeprom 3-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 3-0050: audio processor is MSP3445 (idx 12)
tveeprom 3-0050: decoder processor is SAA7115 (idx 19)
tveeprom 3-0050: has radio, has IR remote
pvrusb2 eeprom detected v4l tveeprom module
pvrusb2 eeprom direct call results:
pvrusb2 has_radio=1
pvrusb2 tuner_type=47
pvrusb2 tuner_formats=0x1000
pvrusb2 audio_processor=10
pvrusb2 model=29032
pvrusb2 revision=9508248
pvrusb2 serial_number=7653922
pvrusb2 rev_str=D168
pvrusb2 Detected video standard NTSC-M (from eeprom)
pvrusb2 Setting initial video standard to NTSC-M (detected from eeprom)
pvrusb2 /*--TRACE_COMMIT--*/ "Brightness" <-- 128 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Contrast" <-- 68 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Saturation" <-- 64 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Volume" <-- 65535 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Audio Bitrate" <-- 3 (224kb/s)
pvrusb2 /*--TRACE_COMMIT--*/ "Audio CRC" <-- 1 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Average video bitrate" <-- 6000000 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Peak video bitrate" <-- 6000000 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Audio Mode" <-- 1 (Stereo)
pvrusb2 /*--TRACE_COMMIT--*/ "Tuner Frequency (Hz)" <-- 175250000 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Horizontal capture resolution" <-- 720 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Vertical capture resolution" <-- 480 (<integer>)
pvrusb2 /*--TRACE_COMMIT--*/ "Audio Layer" <-- 2 (<integer>)
pvrusb2 i2c 0x61 tuner handler set up
pvrusb2 Probed: ctxt=f71bab20 ctl_mask=0x2f (tuner unset) @ 0x61 (handler: pvrusb2-tuner) [v4l2_standard v4l2_bcsh v4l2_volume v4l2_freq v4l2_size]
pvrusb2 i2c 0x40 msp3400 V4L1 handler set up
pvrusb2 Probed: ctxt=f720c780 ctl_mask=0x1c0 MSP3445G-B8 @ 0x40 (handler: pvrusb2-audio) [v4l1_standard v4l1_volume v4l1_freq]
pvrusb2 i2c 0x21 saa711x V4L2 handler set up
pvrusb2 Probed: ctxt=f720c580 ctl_mask=0x2f saa7115 @ 0x21 (handler: pvrusb2-video-v4l) [v4l2_standard v4l2_bcsh v4l2_volume v4l2_freq v4l2_size]
pvrusb2 i2c 0x43 tda9887 V4L2 handler set up
pvrusb2 Probed: ctxt=f720c540 ctl_mask=0x2f tda9887 @ 0x43 (handler: pvrusb2-demod) [v4l2_standard v4l2_bcsh v4l2_volume v4l2_freq v4l2_size]
pvrusb2 i2c tuner set_type(47)
tuner 3-0061: type set to 47 (LG NTSC (TAPE series))
pvrusb2 i2c msp3400 set_stereo
pvrusb2 i2c v4l2 set_input(0)
pvrusb2 i2c v4l2 set_audio 0
pvrusb2 i2c demod set_config(0x0)
pvrusb2 i2c v4l2 set_standard(0)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
pvrusb2 i2c v4l2 set_bcsh b=128 c=68 s=64 h=0
pvrusb2 i2c v4l2 set_volume(vol=65535 bal=0 bas=0 treb=0 mute=0)
pvrusb2 i2c v4l2 set_freq(175250000)
pvrusb2 i2c v4l2 set_size(720x480)
pvrusb2 i2c v4l1 set_standard(0)
pvrusb2 i2c v4l1 set_volume(vol=65535 bal=0 bas=0 treb=0 mute=0)
pvrusb2 i2c v4l1 set_freq(175250000)
pvrusb2 pvr2_stream_create: sp=f707d4a0
pvrusb2 pvr2_hdw_setup: video stream is f707d4a0
pvrusb2 pvr2_hdw_setup(hdw=f7202000) done, ok=1 init_ok=1
pvrusb2 Device initialization completed successfully.
pvrusb2 Registered pvrusb2 v4l device, minor=0
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
EXT3 FS on hdb8, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb11, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb13, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1052248k swap on /dev/hda3. Priority:-1 extents:1 across:1052248k
Adding 1574328k swap on /dev/hdb6. Priority:-2 extents:1 across:1574328k
ip_tables: (C) 2000-2002 Netfilter core team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 232 bytes per conntrack
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
tg3: eth1: Link is up at 100 Mbps, full duplex.
tg3: eth1: Flow control is off for TX and off for RX.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
lirc_dev: no version for "struct_module" found: kernel tainted.
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
cx2388x v4l2 driver version 0.0.5 loaded
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
pvrusb2 i2c_attach [client=Hauppauge IR @ 0x18 ctxt=dc6995c0]
pvrusb2 Probed: ctxt=dc6995c0 ctl_mask=0x2f Hauppauge IR @ 0x18 [v4l2_standard v4l2_bcsh v4l2_volume v4l2_freq v4l2_size]
pvrusb2 i2c v4l2 set_standard(0)
pvrusb2 i2c v4l2 set_bcsh b=128 c=68 s=64 h=0
pvrusb2 i2c v4l2 set_volume(vol=65535 bal=0 bas=0 treb=0 mute=0)
pvrusb2 i2c v4l2 set_freq(175250000)
pvrusb2 i2c v4l2 set_size(720x480)
lirc_dev: lirc_register_plugin: sample_rate: 10
lirc_serial: auto-detected active high receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
pvrusb2 pvr2_v4l2_do_ioctl failure, ret=-22 cmd=-1068739046 (0xc04c561a)
pvrusb2 /*--TRACE_COMMIT--*/ "Video Source" <-- 2 (composite)
pvrusb2 i2c msp3400 set_stereo
pvrusb2 i2c v4l2 set_input(2)
pvrusb2 pvr2_v4l2_do_ioctl failure, ret=-22 cmd=-1068739046 (0xc04c561a)
pvrusb2 /*--TRACE_COMMIT--*/ "Contrast" <-- 63 (<integer>)
pvrusb2 i2c v4l2 set_bcsh b=128 c=63 s=64 h=0
pvrusb2 /*--TRACE_COMMIT--*/ "Saturation" <-- 63 (<integer>)
pvrusb2 i2c v4l2 set_bcsh b=128 c=63 s=63 h=0
pvrusb2 /*--TRACE_COMMIT--*/ "Brightness" <-- 127 (<integer>)
pvrusb2 i2c v4l2 set_bcsh b=127 c=63 s=63 h=0
input: PC Speaker as /class/input/input2
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:22:51 PST 2005
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
application mixer_applet2 uses obsolete OSS audio interface
pvrusb2 /*--TRACE_COMMIT--*/ "Volume" <-- 58950 (<integer>)
pvrusb2 i2c v4l2 set_volume(vol=58950 bal=0 bas=0 treb=0 mute=0)
pvrusb2 i2c v4l1 set_volume(vol=58950 bal=0 bas=0 treb=0 mute=0)
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_setup (setup) id=db0116a0
pvrusb2 /*--TRACE_STREAM--*/ enable
pvrusb2 subsys mask changing 0x1f:0xffffffff from 0x1 to 0x1f
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_configure
pvrusb2 /*---TRACE_CTL----*/ decoder enable
pvrusb2 i2c v4l2 decoder_enable(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_hdw_cmd_usbstream(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_start
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_start id=db0116a0
pvrusb2 /*--TRACE_STREAM--*/ disable
pvrusb2 subsys mask changing 0x1e:0x0 from 0x1f to 0x1
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_stop
pvrusb2 /*---TRACE_CTL----*/ pvr2_hdw_cmd_usbstream(0)
pvrusb2 /*---TRACE_CTL----*/ decoder disable
pvrusb2 i2c v4l2 decoder_enable(0)
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_setup (tear-down) id=db0116a0
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_stop id=db0116a0
application firefox-bin uses obsolete OSS audio interface
pvrusb2 /*--TRACE_COMMIT--*/ "Volume" <-- 65500 (<integer>)
pvrusb2 i2c v4l2 set_volume(vol=65500 bal=0 bas=0 treb=0 mute=0)
pvrusb2 i2c v4l1 set_volume(vol=65500 bal=0 bas=0 treb=0 mute=0)
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_setup (setup) id=e88f12e0
pvrusb2 /*--TRACE_STREAM--*/ enable
pvrusb2 subsys mask changing 0x1f:0xffffffff from 0x1 to 0x1f
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_configure
pvrusb2 /*---TRACE_CTL----*/ decoder enable
pvrusb2 i2c v4l2 decoder_enable(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_hdw_cmd_usbstream(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_start
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_start id=e88f12e0
pvrusb2 /*--TRACE_STREAM--*/ disable
pvrusb2 subsys mask changing 0x1e:0x0 from 0x1f to 0x1
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_stop
pvrusb2 /*---TRACE_CTL----*/ pvr2_hdw_cmd_usbstream(0)
pvrusb2 /*---TRACE_CTL----*/ decoder disable
pvrusb2 i2c v4l2 decoder_enable(0)
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_setup (tear-down) id=e88f12e0
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_stop id=e88f12e0
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_setup (setup) id=e88f13e0
pvrusb2 /*--TRACE_STREAM--*/ enable
pvrusb2 subsys mask changing 0x1f:0xffffffff from 0x1 to 0x1f
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_configure
pvrusb2 /*---TRACE_CTL----*/ decoder enable
pvrusb2 i2c v4l2 decoder_enable(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_hdw_cmd_usbstream(1)
pvrusb2 /*---TRACE_CTL----*/ pvr2_encoder_start
pvrusb2 /*---TRACE_READ---*/ pvr2_ioread_start id=e88f13e0
adjusting scr: 58064
em8300_video.o: Video sync rdptr is stuck at 0x00015f03, wrptr 0x00016190, left 653
em8300_video.o: Video sync timeout
--
Roger J. Allen Voice: (312)-587-0690
Internet: rja at rogera.net FAX: (312)-587-0691
More information about the pvrusb2
mailing list